Auto Manual of VW Passat B5



VW Passat
The maintenance instruction
1. Maintenance service
2. Engines
3. Cooling system
4. Fuel system
5. Engine management
6. An exhaust system
7. Transmission
8. A running gear
9. A steering
- 10. Brake system
   10.2. The general information
   10.3. Systems ABS/EBV/EDS/ASR/ESP
   10.4. Check of the vacuum amplifier of brakes
    10.5. Replacement of lobbies brake колодок
   10.6. Replacement back brake колодок
   10.7. Check of a brake disk
   10.8. A brake disk
   10.9. Prorolling of hydraulic brake system
    10.10. Brake pipelines and hoses
   10.11. The stoplight switch
   10.12. The lever of a manual brake
   10.13. Adjustment of a manual brake
    10.14. A cable of a manual brake
   10.15. The basic malfunctions of brakes
11. A body
12. Heating, ventilation
13. An electric equipment



49e3918c

10.13. Adjustment of a manual brake
THE GENERAL DATA

Cable of a manual brake

1 – an adjusting nut,
2 – a cover of a cable of a manual brake,
3 – a cover of a cable of a manual brake,
4 – a clamp

Муфта a cable of a manual brake

1 – adjusting муфта,
5 – a colour sealing ring

The prevention

The optimum backlash brake колодок is supported by the mechanism of automatic adjustment, however, at replacement of cables of a manual brake or a back support of brakes it is necessary to make adjustment of a manual brake.


PERFORMANCE ORDER
1. At least once press against the stop a brake pedal.
2. Completely release a manual brake.
3. Having pulled upwards, take an ashtray from a back part of the central console.
4. Ослабьте bolts of fastening of back wheels, then lift a back part of the car and fix on supports. Remove back wheels.
5. Remove from the jack of cables of a manual brake plastic details which are not subject to a reuse.
6. A screw-driver edge fix the jack of cables of a manual brake from поворачивания.
7. Adjust a cable of a manual brake as follows.
8. Remove a clamp (4) (fig. the Cable of a manual brake see).
9. Rotating an adjusting nut, tighten it against the stop, thus the flute for a clamp should be blocked.
10. Move covers of a cable of a manual brake (2 and 3) (fig. the Cable of a manual brake see) towards each other.
11. Rotate an adjusting nut in the opposite direction before occurrence of a fillet for a clamp.
12. Establish a clamp.
13. Having pulled every which way, stretch covers of a cable of a manual brake (2 and 3) (fig. the Cable of a manual brake see) on both cables of a manual brake to a full tension of a cable (arrow). Thus check up, that the lever of a manual brake on a support has not moved.
14. Take a screw-driver from the jack of cables of a manual brake and some times tighten a manual brake.
15. Check up correctness of a tension of cables of a manual brake. At a correct tension of cables of a manual brake the distance () between the lever of a manual brake and a brake support should be no more than 1,5 mm.
16. Otherwise make repeated adjustment for what, unscrewing or screwing up adjusting муфту (1) (fig. of Mufta of a cable of a manual brake see), adjust a cable of a manual brake so that the distance between the lever of a manual brake and a support made no more than 1,5 mm.
The prevention

At adjustment carrying out rotate adjusting муфту so that the colour sealing ring from an end face adjusting муфты did not act. Otherwise water and a dirt will get to an element of adjustment of a cable of a manual brake.


17. Establish and screw bolts back wheels.
18. Lower the car on the earth and tighten bolts of fastening of wheels the moment of 120 Nanometers.
19. Establish into place an ashtray.