Auto Manual of VW Passat B5



VW Passat
The maintenance instruction
1. Maintenance service
2. Engines
3. Cooling system
4. Fuel system
5. Engine management
6. An exhaust system
7. Transmission
8. A running gear
9. A steering
10. Brake system
- 11. A body
   11.2. Care of a body
   11.3. Care of an upholstery and rugs
   11.4. Repair of insignificant damages of a body
   11.5. Repair of strong damages of a body
    11.6. The forward cross-section panel
   11.7. A forward bumper
   11.8. Removal of the lever of blocking of a cowl
   11.9. Adjustment of a lateral directing arm of a bumper
   11.10. A back bumper
   11.11. A forward wing
   11.12. Facing of a niche of a forward wheel
   11.13. An air inlet lattice
    11.14. A cowl
   11.15. A radiator lattice
    11.16. A cable of opening of the lock of a cowl
   11.17. The cowl lock
   11.18. Internal furnish of a door
   11.19. Differences at removal of an upholstery of the right forward door
   11.20. The block of management of door mechanisms
   11.21. Door consolidation
   11.22. Lateral furnish of a luggage space of models the Sedan
   11.23. Lateral furnish of a luggage space of models the Versatile person
   11.24. Back furnish of a luggage space on models the Sedan
   11.25. An upholstery of a cover of a luggage carrier
   11.26. An upholstery of a door of a luggage carrier
   11.27. A covering of a floor of a luggage space on models the Versatile person
   11.28. A luggage carrier cover
    11.29. The luggage carrier lock
   11.30. Adjustment of position of a cover of a luggage carrier / a back door
    11.31. The lock of a back door on models the Versatile person
   11.32. A forward door
   11.33. The cylinder of the lock of a forward door
   11.34. The external handle of opening of a door
   11.35. The door lock
   11.36. Manual lowering of glass of a door
   11.37. Door glass
   11.38. A door arm
   11.39. An internal rear-view mirror
   11.40. The central console
   11.41. A forward ashtray
   11.42. A back ashtray
   11.43. A decorative overlay of the lever (an automatic transmission)
   11.44. Decorative overlays under a radio receiver
   11.45. The bottom furnish of the panel of devices from outside the driver
   11.46. A ware box
   11.47. An internal decorative overlay of an external rear-view mirror
   11.48. The ceiling handle
   11.49. Protivosolnechnye peaks
   11.50. Overlays of thresholds
   11.51. Wind and back has flown down
   11.52. Sitting lobbies
   11.53. A headrest
   11.54. Lateral pillows of safety
   11.55. Back sitting
   11.56. The left back of back sitting
   11.57. A carpet covering
   11.58. Elements of furnish of an interior
   11.59. An external mirror of a back kind/glass of a mirror
   11.60. The case of an external mirror
   11.61. The Protection/bordjurnaja a roof lath
   11.62. A lateral overlay of a body
   11.63. Replacement of rubber tapes of brushes of screen wipers
   11.64. Nozzles of washers of a windscreen
   11.65. Screen wiper levers
12. Heating, ventilation
13. An electric equipment



49e3918c

11. A body

11.1. The general information
THE GENERAL DATA

Cars Passat have bearing body. The body represents universal цельносварную a design and includes zones смятия at collision in front and in a back part with a safety cell in the car centre.

The cowl, cover of a luggage carrier, door and forward wings fasten on bolts and are easily replaced. At installation it is necessary to observe backlashes, otherwise, for example, the door will knock or the raised noise from a wind will be observed at movement. The backlash should be, at least, parallel on the extent, i.e. The distance between body parts should be maintained to constants on all length of a crack.

In the course of manufacture the car body is zinced, and the bottom is processed by an anticorrosive covering. Bumpers and loose leaves of an arch of a wheel for durability and durability are made of plastic.

Almost all knots and details of the equipment of a body can be established and act in film by means of a usual set инструмен тов. At dismantling and assemblage it is necessary to accept special safety measures not to put serious damages to consolidations and the anticorrosive covering put by manufacturer.


The prevention

If you have enough experience, or there is no suitable place for performance of any works stated in this management to carry out repair the Volkswagen or in a specialised repair truck is recommended in service of car-care centre of the dealer.

Before the beginning of works with the panel of devices, дверьми or any devices of an electric equipment remove a wire of weight from the accumulator.


Security measures at carrying out of welding works

At carrying out of the welding and other works connected with strong искровыделением nearby from a site of the accumulator, necessarily remove the accumulator.

It is forbidden to spend welding both a firm and soft soldering of details заполненно го the conditioner. It concerns and those elements of the car which welding can cause a warming up of details of the conditioner. At carrying out it is repair-okrasoch ных works in сушильной to the chamber or in a zone of its warming up the temperature should not exceed 80 .

The receiver with code protection against plunder


The prevention

Before a detachment of a wire of weight from the accumulator be convinced that you know a correct code раскодировки the receiver which restores its working capacity. If after connection of a wire of weight to enter a wrong code the receiver will be disconnected.


Connection of a body with weight
The prevention

To keep reliability of connection with weight and to prevent damage owing to corrosion it is not necessary to disconnect wires from a body. Disconnect wires only from the accumulator, the engine or a transmission.


Before joining of wires or tyres of connection with weight clear all places of connections to metal. Be convinced of reliability of an inhaling болтовых connections with weight.