Auto Manual of VW Passat B5

VW Passat
The maintenance instruction
1. Maintenance service
2. Engines
3. Cooling system
4. Fuel system
5. Engine management
6. An exhaust system
7. Transmission
8. A running gear
9. A steering
10. Brake system
- 11. A body
   11.2. Care of a body
   11.3. Care of an upholstery and rugs
   11.4. Repair of insignificant damages of a body
   11.5. Repair of strong damages of a body
    11.6. The forward cross-section panel
   11.7. A forward bumper
   11.8. Removal of the lever of blocking of a cowl
   11.9. Adjustment of a lateral directing arm of a bumper
   11.10. A back bumper
   11.11. A forward wing
   11.12. Facing of a niche of a forward wheel
   11.13. An air inlet lattice
    11.14. A cowl
   11.15. A radiator lattice
    11.16. A cable of opening of the lock of a cowl
   11.17. The cowl lock
   11.18. Internal furnish of a door
   11.19. Differences at removal of an upholstery of the right forward door
   11.20. The block of management of door mechanisms
   11.21. Door consolidation
   11.22. Lateral furnish of a luggage space of models the Sedan
   11.23. Lateral furnish of a luggage space of models the Versatile person
   11.24. Back furnish of a luggage space on models the Sedan
   11.25. An upholstery of a cover of a luggage carrier
   11.26. An upholstery of a door of a luggage carrier
   11.27. A covering of a floor of a luggage space on models the Versatile person
   11.28. A luggage carrier cover
    11.29. The luggage carrier lock
   11.30. Adjustment of position of a cover of a luggage carrier / a back door
    11.31. The lock of a back door on models the Versatile person
   11.32. A forward door
   11.33. The cylinder of the lock of a forward door
   11.34. The external handle of opening of a door
   11.35. The door lock
   11.36. Manual lowering of glass of a door
   11.37. Door glass
   11.38. A door arm
   11.39. An internal rear-view mirror
   11.40. The central console
   11.41. A forward ashtray
   11.42. A back ashtray
   11.43. A decorative overlay of the lever (an automatic transmission)
   11.44. Decorative overlays under a radio receiver
   11.45. The bottom furnish of the panel of devices from outside the driver
   11.46. A ware box
   11.47. An internal decorative overlay of an external rear-view mirror
   11.48. The ceiling handle
   11.49. Protivosolnechnye peaks
   11.50. Overlays of thresholds
   11.51. Wind and back has flown down
   11.52. Sitting lobbies
   11.53. A headrest
   11.54. Lateral pillows of safety
   11.55. Back sitting
   11.56. The left back of back sitting
   11.57. A carpet covering
   11.58. Elements of furnish of an interior
   11.59. An external mirror of a back kind/glass of a mirror
   11.60. The case of an external mirror
   11.61. The Protection/bordjurnaja a roof lath
   11.62. A lateral overlay of a body
   11.63. Replacement of rubber tapes of brushes of screen wipers
   11.64. Nozzles of washers of a windscreen
   11.65. Screen wiper levers
12. Heating, ventilation
13. An electric equipment

Корисні властивості родзинок

11.63. Replacement of rubber tapes of brushes of screen wipers

THE GENERAL DATA

Regularly check an overall performance of brushes of a screen wiper. The friction of brushes on the iced over surface of glasses leads to damage of rubber tapes of brushes of a screen wiper. The polluted brushes of a screen wiper wipe soft rags and special means.
It is necessary to replace brushes at which the rubber tape has hardened, has cracked or has become covered by silicone.

Removal

PERFORMANCE ORDER

1. Lift the brush lever стеклоочистите ля from a windscreen. Turn a screen wiper brush at an angle 90 to the screen wiper lever.

2. Press a brush clamp стеклоочисти теля (marksman), then move a brush on the lever (marksman) and, moving it in the opposite direction, remove from the screen wiper lever.

3. From two parties compress steel amplifiers of a rubber tape of a screen wiper and take a rubber tape of a screen wiper from a brush end face.

Installation

Arrangement of dredging of a clamp on a rubber tape of a brush of a screen wiper

PERFORMANCE ORDER

1. Insert a new rubber tape without steel amplifiers into the bottom clips of a brush of a screen wiper.

2. Insert steel amplifiers into the first flute of a rubber tape.

3. Пассатижами compress steel amplifiers together with a rubber tape and insert them into the top clip of a brush of a screen wiper. Thus clip short moustaches should enter into clamps on a rubber tape, the Arrangement of dredging of a clamp fig. see a rubber tape of a brush of a screen wiper.

4. Establish screen wiper brushes on levers in sequence, return to removal. Thus the clamp should fix accurately a brush on the screen wiper lever.

5. Lower the screen wiper lever on a windscreen.