Auto Manual of VW Passat B5

VW Passat
The maintenance instruction
1. Maintenance service
2. Engines
3. Cooling system
4. Fuel system
5. Engine management
6. An exhaust system
7. Transmission
8. A running gear
9. A steering
10. Brake system
- 11. A body
   11.2. Care of a body
   11.3. Care of an upholstery and rugs
   11.4. Repair of insignificant damages of a body
   11.5. Repair of strong damages of a body
    11.6. The forward cross-section panel
   11.7. A forward bumper
   11.8. Removal of the lever of blocking of a cowl
   11.9. Adjustment of a lateral directing arm of a bumper
   11.10. A back bumper
   11.11. A forward wing
   11.12. Facing of a niche of a forward wheel
   11.13. An air inlet lattice
    11.14. A cowl
   11.15. A radiator lattice
    11.16. A cable of opening of the lock of a cowl
   11.17. The cowl lock
   11.18. Internal furnish of a door
   11.19. Differences at removal of an upholstery of the right forward door
   11.20. The block of management of door mechanisms
   11.21. Door consolidation
   11.22. Lateral furnish of a luggage space of models the Sedan
   11.23. Lateral furnish of a luggage space of models the Versatile person
   11.24. Back furnish of a luggage space on models the Sedan
   11.25. An upholstery of a cover of a luggage carrier
   11.26. An upholstery of a door of a luggage carrier
   11.27. A covering of a floor of a luggage space on models the Versatile person
   11.28. A luggage carrier cover
    11.29. The luggage carrier lock
   11.30. Adjustment of position of a cover of a luggage carrier / a back door
    11.31. The lock of a back door on models the Versatile person
   11.32. A forward door
   11.33. The cylinder of the lock of a forward door
   11.34. The external handle of opening of a door
   11.35. The door lock
   11.36. Manual lowering of glass of a door
   11.37. Door glass
   11.38. A door arm
   11.39. An internal rear-view mirror
   11.40. The central console
   11.41. A forward ashtray
   11.42. A back ashtray
   11.43. A decorative overlay of the lever (an automatic transmission)
   11.44. Decorative overlays under a radio receiver
   11.45. The bottom furnish of the panel of devices from outside the driver
   11.46. A ware box
   11.47. An internal decorative overlay of an external rear-view mirror
   11.48. The ceiling handle
   11.49. Protivosolnechnye peaks
   11.50. Overlays of thresholds
   11.51. Wind and back has flown down
   11.52. Sitting lobbies
   11.53. A headrest
   11.54. Lateral pillows of safety
   11.55. Back sitting
   11.56. The left back of back sitting
   11.57. A carpet covering
   11.58. Elements of furnish of an interior
   11.59. An external mirror of a back kind/glass of a mirror
   11.60. The case of an external mirror
   11.61. The Protection/bordjurnaja a roof lath
   11.62. A lateral overlay of a body
   11.63. Replacement of rubber tapes of brushes of screen wipers
   11.64. Nozzles of washers of a windscreen
   11.65. Screen wiper levers
12. Heating, ventilation
13. An electric equipment

11.65. Screen wiper levers Removal

PERFORMANCE ORDER

1. Include, and then switch off a screen wiper so that the screen wiper lever was established in a starting position.

2. On a windscreen screen wiper unscrew a casing in the basis of the lever of a screen wiper.

3. On a screen wiper of back glass move upwards a casing located in the basis of the lever of a screen wiper. On some turns unscrew a nut of fastening of the lever of a screen wiper.

4. Moving the screen wiper lever to the parties, ослабьте its landing to axes, then unscrew a nut and remove the screen wiper lever.

Installation

Starting position of a brush of a screen wiper

Screen wiper of a windshield And = 20 mm.
Screen wiper of back glass And = 20–30 mm.

PERFORMANCE ORDER

1. Establish the screen wiper lever in such position that the brush of a screen wiper of a windscreen settled down on distance of 20 mm from a windscreen, fig. the Starting position of a brush of a screen wiper see. The lever of a screen wiper of back glass establish so that the screen wiper brush was on distance of 20-30 mm over a glass bottom edge. Fix the lever of a screen wiper a nut, having tightened its moment of 15 Nanometers.

2. Establish into place the bottom casing of the lever of a screen wiper.

3. Check up a corner of installation of the lever of a screen wiper and, if necessary, Adjust it.