The maintenance instruction
1. Maintenance service
3. Cooling system
4. Fuel system
5. Engine management
6. An exhaust system
8. A running gear
9. A steering
10. Brake system
11. A body
12. Heating, ventilation
- 13. An electric equipment
13.2. The general information
13.3. Electric chains
13.4. Safety locks
13.5. Rules of care of the accumulator
13.6. Accumulator check
13.7. Accumulator gymnastics
13.8. The accumulator
13.9. Gymnastics system
13.10. The generator
13.11. Replacement of brushes of the generator and a pressure regulator
13.12. System of start of the engine
13.13. A starter
13.14. The traction relay of a starter
13.15. Replacement of bulbs of external illumination
13.16. Replacement of bulbs of internal illumination
13.17. Devices of external illumination
13.18. The executive engine of the proof-reader of light of headlights
13.19. Adjustment of light of headlights
13.20. Gas-discharge lamps of headlights of a passing light
13.21. A combination of devices
13.22. Multipurpose switches of a steering column
13.24. A radio receiver
13.25. High-frequency loudspeakers
13.26. Low-frequency loudspeakers
13.27. The aerial
13.28. Check of a heater of back glass
13.29. The engine of a screen wiper of a windscreen
13.30. The engine of a screen wiper of back glass
13.31. The pump стеклоомывателя
13.32. System of the central blocking of locks
13.33. The basic malfunctions of the generator
13.34. The basic malfunctions of a starter
13.35. Electric schemes
Arrangement of a radio receiver and loudspeakers in the car
| 1 – high-frequency loudspeakers on forward doors,
2 – low-frequency loudspeakers on forward doors,
3 – high-frequency loudspeakers on back doors,
4 – low-frequency loudspeakers on back doors,
5 – a radio receiver on the panel of devices
The radio receiver established at factory has a pocket thanks to which process of removal and radio receiver installation is facilitated. For radio receiver removal it is necessary to use two special keys.
The special key used for removal of a radio receiver from the car
Arrangement of narrow cracks for installation of special keys at radio receiver extraction
Use of special keys for extraction of a radio receiver from a nest in the panel of devices
| PERFORMANCE ORDER
| 1. Switch off ignition.
| 2. Remove a wire of weight from the accumulator.
At removal of a wire of weight from the accumulator contents of cells of memory of electronic blocks of management and a radio receiver are erased.
| 3. As the standard equipment on the car the radio receiver, having the coded device against theft which is executed on the basis of the microprocessor is established. After switching-off of a radio receiver from an electric network of the car (removal of the storage battery, removal of a radio receiver or initial installation of a radio receiver) is necessary to enter a safety code. The radio receiver can be included only after input of a correct code.
|4. Before removal of a wire of weight from the accumulator check up, whether there is for you a radio receiver code. In the absence of a safety code to place in operation a radio receiver it is possible only at specialised station a Volkswagen. The individual code of safety of a radio receiver is available in the engineering specifications put to the car at sale.
|5. For radio receiver removal it is necessary to use two special keys 3316, fig. the Special key used for removal of a radio receiver from the car see.
|6. Insert two keys into the narrow cracks located from two parties of a radio receiver before fixing of keys, fig. the Arrangement of narrow cracks for installation of special keys at radio receiver extraction see.
|7. For heads of keys take a radio receiver from a nest (fig. Use of special keys for extraction of a radio receiver from a nest in the panel of devices see). At extraction do not warp a radio receiver and do not pull it aside.
|8. Remove special keys for what wring out downwards lateral clamps of a radio receiver.
|9. Disconnect from a radio receiver electric sockets of loudspeakers and the aerial, and also a multicontact socket of giving of pressure to a radio receiver. If for connection multicontact sockets are used not, before a detachment of sockets mark them.
| PERFORMANCE ORDER
| 1. Connect electric sockets to a back part of a radio receiver.
| 2. Insert a radio receiver into a nest of the panel of devices to защелкивания spring clamps.
| 3. Connect a weight wire to the accumulator.
4. After radio receiver installation enter a safety code. On radio receivers with a safety code on a forward key there is a red emblem in the form of a key. The individual code of safety of a radio receiver is available in the engineering specifications put to the car at sale. Store record of an individual code in a safe place and never hold it in the car.
|5. Enter a code of safety of a radio receiver as follows.
|6. Include a radio receiver.
|7. Simultaneously press keys TR and THAT before occurrence of indication 1000, then release keys.
|8. Enter a safety code, using keys of a choice of stations with 1 on 4. The key 1 defines the first number of a code, a key 2 – the second number of a code etc.
|9. Again simultaneously press keys TR and THAT before occurrence of indication SAVE, then release keys. Now the receiver is placed in operation, and on the display frequency of accepted radio station is highlighted. If the safety code has been correctly entered into a radio receiver after extraction of a key from the ignition lock the light-emitting diode close to an inscription of the name of a radio receiver should blink.
If the safety code has been incorrectly entered into a radio receiver, inscription SAVE at first will start blinking, and then will light up constantly. After that it is possible to repeat process of input of a code of safety only once. At repeated wrong input of a code of safety the radio receiver will be blocked and within an hour it cannot be placed in operation. In an hour during which the radio receiver should be included, repeat input of a code of safety.